Mouse Out CHOP
The Mouse Out CHOP forces the mouse position and button status to be driven from TouchDesigner using the incoming CHOP channels. The
ty channels works in normalized coordinates, ranging from 0 to 1 for the left-to-right and bottom-to-top of the full desktop. If the Desktop is spread over two monitors, tx == 1 is the right of the second monitor.
WARNING: If the incoming channels are changing every frame, it may be difficult to regain control of the mouse without using the keyboard or some other means to kill or suspend the process. However the Mouse Out CHOP does not control the mouse while the incoming channels are constant.
Parameters - Control Page
posu - Channel name to look for that will drive the mouse U position.
posv - Channel name to look for that will drive the mouse V position.
lbuttonname - Channel name to look for that will drive the mouse's left button state.
rbuttonname - Channel name to look for that will drive the mouse's right button state.
mbuttonname - Channel name to look for that will drive the mouse's middle button state.
Cook Every Frame
cookalways - Forces CHOP to cook every frame.
Parameters - Common Page
timeslice - Turning this on forces the channels to be "Time Sliced". A Time Slice is the time between the last cook frame and the current cook frame.
scope - To determine which channels get affected, some CHOPs use a Scope string on the Common page. See Pattern Matching.
Sample Rate Match
srselect - ⊞ - Handle cases where multiple input CHOPs' sample rates are different. When Resampling occurs, the curves are interpolated according to the Interpolation Method Option, or "Linear" if the Interpolate Options are not available.
- Resample At First Input's Rate
first- Use rate of first input to resample others.
- Resample At Maximum Rate
max- Resample to the highest sample rate.
- Resample At Minimum Rate
min- Resample to the lowest sample rate.
- Error If Rates Differ
err- Doesn't accept conflicting sample rates.
exportmethod - ⊞ - This will determine how to connect the CHOP channel to the parameter. Refer to the Export article for more information.
- DAT Table by Index
datindex- Uses the docked DAT table and references the channel via the index of the channel in the CHOP.
- DAT Table by Name
datname- Uses the docked DAT table and references the channel via the name of the channel in the CHOP.
- Channel Name is Path:Parameter
autoname- The channel is the full destination of where to export to, such has
autoexportroot - This path points to the root node where all of the paths that exporting by Channel Name is Path:Parameter are relative to.
exporttable - The DAT used to hold the export information when using the DAT Table Export Methods (See above).
- Input 0: -
Info CHOP Channels
Extra Information for the Mouse Out CHOP can be accessed via an Info CHOP.
Common CHOP Info Channels
- start - Start of the CHOP interval in samples.
- length - Number of samples in the CHOP.
- sample_rate - The samplerate of the channels in frames per second.
- num_channels - Number of channels in the CHOP.
- time_slice - 1 if CHOP is Time Slice enabled, 0 otherwise.
- export_sernum - A count of how often the export connections have been updated.
Common Operator Info Channels
- total_cooks - Number of times the operator has cooked since the process started.
- cook_time - Duration of the last cook in milliseconds.
- cook_frame - Frame number when this operator was last cooked relative to the component timeline.
- cook_abs_frame - Frame number when this operator was last cooked relative to the absolute time.
- cook_start_time - Time in milliseconds at which the operator started cooking in the frame it was cooked.
- cook_end_time - Time in milliseconds at which the operator finished cooking in the frame it was cooked.
- cooked_this_frame - 1 if operator was cooked this frame.
- warnings - Number of warnings in this operator if any.
- errors - Number of errors in this operator if any.