The FreeD CHOP reads incoming camera tracking data sent over a network using the FreeD protocol and outputs CHOP channels that can be used to control a virtual 3D camera.
The channels exported by the FreeD CHOP are:
- camera_id - a number from 0 - 255 that can be used to store an id number for the camera
- tx, ty, tz - camera position, can be connected to the Camera COMP Translate parameters
- rx, ry, rz - camera rotation, can be connected to the Camera COMP Rotate parameters
- focus - a 24-bit positive integer (0-16 million) in arbitrary units that relates to the focus ring on a camera lens. Applications can interpret this value according to the hardware in use.
- zoom - a 24-bit positive integer (0-16 million) in arbitrary units that relates to the zoom ring on a camera lens. Applications can interpret this value according to the hardware in use.
- user - a 16-bit positive integer (0 - 65k) that can be used by the camera system to send custom user-defined data
Note: The FreeD CHOP only processes the 'D1' camera position and orientation message that is part of the FreeD protocol. All other message types will be ignored.
For more information or to diagnose connection problems, an Info CHOP can be connected to see if any packets have been dropped or skipped.
Parameters - FreeD Page
active - While On, the CHOP receives FreeD information sent to the network port. While Off, no updating occurs.
protocol - ⊞ - The network protocol to use. Refer to the Network Protocols article for more information.
- Messaging (UDP)
- Multi-Cast Messaging (UDP)
netaddress - When using Multicast, this is the address that FreeD will listen for packets on.
port - The port which FreeD will accept packets on.
localaddress - ⊞ - Specify an IP address to receive on, useful when the system has mulitple NICs (Network Interface Card) and you want to select which one to use.
Parameters - Common Page
timeslice - Turning this on forces the channels to be "Time Sliced". A Time Slice is the time between the last cook frame and the current cook frame.
scope - To determine which channels get affected, some CHOPs use a Scope string on the Common page.
Sample Rate Match
srselect - ⊞ - Handle cases where multiple input CHOPs' sample rates are different. When Resampling occurs, the curves are interpolated according to the Interpolation Method Option, or "Linear" if the Interpolate Options are not available.
- Resample At First Input's Rate
first- Use rate of first input to resample others.
- Resample At Maximum Rate
max- Resample to the highest sample rate.
- Resample At Minimum Rate
min- Resample to the lowest sample rate.
- Error If Rates Differ
err- Doesn't accept conflicting sample rates.
exportmethod - ⊞ - This will determine how to connect the CHOP channel to the parameter. Refer to the Export article for more information.
- DAT Table by Index
datindex- Uses the docked DAT table and references the channel via the index of the channel in the CHOP.
- DAT Table by Name
datname- Uses the docked DAT table and references the channel via the name of the channel in the CHOP.
- Channel Name is Path:Parameter
autoname- The channel is the full destination of where to export to, such has
autoexportroot - This path points to the root node where all of the paths that exporting by Channel Name is Path:Parameter are relative to.
exporttable - The DAT used to hold the export information when using the DAT Table Export Methods (See above).
Info CHOP Channels
Extra Information for the FreeD CHOP can be accessed via an Info CHOP.
Specific FreeD CHOP Info Channels
- valid_packets -
- unrecognized_packets -
- corrupt_packets -
Common CHOP Info Channels
- start - Start of the CHOP interval in samples.
- length - Number of samples in the CHOP.
- sample_rate - The samplerate of the channels in frames per second.
- num_channels - Number of channels in the CHOP.
- time_slice - 1 if CHOP is Time Slice enabled, 0 otherwise.
- export_sernum - A count of how often the export connections have been updated.
Common Operator Info Channels
- total_cooks - Number of times the operator has cooked since the process started.
- cook_time - Duration of the last cook in milliseconds.
- cook_frame - Frame number when this operator was last cooked relative to the component timeline.
- cook_abs_frame - Frame number when this operator was last cooked relative to the absolute time.
- cook_start_time - Time in milliseconds at which the operator started cooking in the frame it was cooked.
- cook_end_time - Time in milliseconds at which the operator finished cooking in the frame it was cooked.
- cooked_this_frame - 1 if operator was cooked this frame.
- warnings - Number of warnings in this operator if any.
- errors - Number of errors in this operator if any.