DMX Out CHOP
The first channel you send into the DMX Out will correspond to the first DMX address (DMX channel) As you add channels to the DMX Out, you will access the next DMX channels in order. For example, if you input 12 channels into the DMX out, you will be controlling DMX channels 1 thru 12.
A Routing Table can be provided in a DAT where addresses can be specified by adding rows for each channel and specifying net, subnet and universe.
ENTTEC NOTE: - Use ENTTEC's NMU (Node Management Utility) to configure and inspect the ENTTEC devices found on your network.
macOS NOTE: - ENTTEC USB Pro may not connect automatically, to enable it enter the following command in the Terminal:
sudo kextunload -b com.apple.driver.AppleUSBFTDI
Parameters - DMX Page
active - Connects to the device while On.
interface - ⊞ - Select the type of interface to connect to the device with.
- Enttec Generic Serial
serial- Uses the operating system's serial calls to write data.
- Enttec USB Pro
- Enttec USB Pro Mk2
artnet- Sets the interface to Art-Net protocol.
sacn- Sets the interface to sACN protocol.
format - ⊞ - Select between sending Packet Per Sample or Packet Per Channel.
- Packet Per Sample
packetpersample- Each channel acts as a DMX channel, ie. 512 channels for 1 universe.
- Packet Per Channel
packetperchan- Each sample in a channel acts as a DMX channel. This allows for setting up a channel for each universe, ie. 1 channel with 512 samples for 1 universe. Add multiple channels for multiple universes.
routingtable - Available when using Packet Per Channel Format for Art-Net or sACN. Use the docked Table DAT to route channels to the appropriate universes. Addresses can be specified by adding rows for each channel and specifying net, subnet and universe. The net, subnet and universe columns are optional. If for example the
net column is missing from the Routing Table, the
Net parameter is used instead.
When removing the Routing Table from the parameter, the specified address will be used for the first channel while all other channels are assigned to consecutive addresses.
Note: For sACN the first available universe has the index 1 as universe 0 is reserved by the system for future use.
device - Select a DMX device from the menu.
serialport - When the Interface parameter is set to Generic Serial this parameter lets you select which Serial (COM) port to use.
rate - How often data is sent to the device (per second).
WARNING: DMX512 devices have a maximum refresh rate of 44Hz. It is recommended that Rate <= 44 for reliable performance.
net - When the Interface parameter is set to Art-Net, this sets the net address. A net is a groups of 16 consecutive subnets or 256 consecutive universes. The range for this parameter is 0-127. This is not a network IP address.
subnet - When the Interface parameter is set to Art-Net, this sets the subnet address. A subnet is a group of 16 consecutive universes. The range for this parameter is 0-15. This is not a network subnet mask.
universe - When the Interface parameter is set to Art-Net, this sets the universe address. A single DMX512 frame of 512 channels is referred to as a universe. The range for this parameter is 0-15.
cid - The unique ID of the sender.
source - User assigned name of source (for informative purposes).
priority - The priority of the data being sent, if there are multiple sources.
Parameters - Network Page
multicast - Enable multicast for sACN. Multicast automatically builds the IP based on Net, Subnet, and Universe of the device. This allows for sending to multiple devices at once by specifying multiple universes.
netaddress - Specify the IP address to use when Interface is set to Art-Net. This address corresponds to the receiving device address. When the address is set to its default 255.255.255.255, the messages are instead broadcast to all devices on the network. The Art-Net Net, Subnet and Universe of the receiving devices must still match those specified in the DMX Out CHOP in all cases.
localaddress - When the sending machine is equipped with multiple network adapters, this parameter can be used to choose which adapter to send the data from by specifying its IP address here.
localport - In rare cases it can be necessary to supply a custom port from which the data should be sent. The default of
-1 means the O/S assigned port is being used.
Use Custom Port
customport - Enable the Network Port parameter to specify the port of the receiving hardware.
netport - Let's you specify the port of the receiving hardware. By default and the spec of ArtNet this is set to 6454 and should only be changed in rare cases.
Parameters - Common Page
timeslice - Turning this on forces the channels to be "Time Sliced". A Time Slice is the time between the last cook frame and the current cook frame.
scope - To determine which channels get affected, some CHOPs use a Scope string on the Common page.
Sample Rate Match
srselect - ⊞ - Handle cases where multiple input CHOPs' sample rates are different. When Resampling occurs, the curves are interpolated according to the Interpolation Method Option, or "Linear" if the Interpolate Options are not available.
- Resample At First Input's Rate
first- Use rate of first input to resample others.
- Resample At Maximum Rate
max- Resample to the highest sample rate.
- Resample At Minimum Rate
min- Resample to the lowest sample rate.
- Error If Rates Differ
err- Doesn't accept conflicting sample rates.
exportmethod - ⊞ - This will determine how to connect the CHOP channel to the parameter. Refer to the Export article for more information.
- DAT Table by Index
datindex- Uses the docked DAT table and references the channel via the index of the channel in the CHOP.
- DAT Table by Name
datname- Uses the docked DAT table and references the channel via the name of the channel in the CHOP.
- Channel Name is Path:Parameter
autoname- The channel is the full destination of where to export to, such has
autoexportroot - This path points to the root node where all of the paths that exporting by Channel Name is Path:Parameter are relative to.
exporttable - The DAT used to hold the export information when using the DAT Table Export Methods (See above).
- Input 0 -